DHCP Server 2016 Super Scope Addresses Available Percentage Monitor Monitor

  • ID:  Microsoft.Windows.DHCPServer.10.0.SuperScope.IPV4.AddressesAvailable.Percentage.Monitor
  • Description:  This monitor alerts when the percentage of free addresses for the specified super scope fall below the defined threshold
  • Target:  DHCP Superscope
  • Enabled:  Yes

Operational States

Name State Description
Super Scope Addresses Available Success  
Super Scope Addresses Low Warning  
Super Scope Addresses Very Low Error  

Overridable Parameters

Parameter Name Default Value Description Override
Number of Samples 3 Number of samples to used for the monitor.
Warning Threshold 30 The Warning Threshold value to consider in the monitor type.
Error Threshold 10 The Error Threshold value to consider in the monitor type.
Interval seconds 900 How frequently (in seconds) the value should be sampled.
Sync Time   Synchronization time for the module execution.
Timeout Seconds 300 How much time (in seconds) to wait for the module to finish execution.

Alert Details

Monitor State Message Priority Severity Auto Resolution
Super Scope Addresses Very Low (Error) DHCP Server 2016 Super Scope Percentage of Available Addresses are Low Medium Match Monitor Health Yes

Run As Profiles

Name
Privileged Monitoring Account

Monitor Knowledgebase

Summary

Microsoft Windows Server DHCP 2016 Percentage Super Scope Monitoring, returns a property bag containing the number of free percentage in the specified scope.

These are the parameters that we could override, if need it:

  • Number of Samples: Number of times to wait to calculate the new state of the monitor.

  • Warning Threshold: Minimum Percentage accepted as Healthy State.

  • Error Threshold: Minimum Percentage accepted as Warning State.

  • Interval Seconds: Amount of Seconds for each execution

  • Sync Time: Time expressed with this format: "hh:mm" since you will like to start the execution.

  • Timeout Seconds: Amount of seconds to wait until cancel execution for "timeout reasons."

Causes

Check available scope addresses.

Resolutions

If the DHCP server 2016 does not have IP addresses available to provide to its clients, they could fail to obtain new assigned IPs. When this occurs, consider the following possible solutions:

  • Use scope extension to expand the address range for the current scope.

  • Reduce the lease duration and decrease the cleanup interval. This can help to speed the reclaiming of expired scope IP addresses.

Extend the DHCP scope

If you already have a DHCP scope and the Start Address and End Address do not currently include all addresses for your specific subnet, you can increase the number of addresses in the scope by extending the Start Address or End Address in the scope properties.

To increase the number of addresses available to clients:

  • At the DHCP server, click Start, point to Administrative Tools, and then click DHCP.

  • In the console tree, right-click the scope you want to extend, and then click Properties.

  • Change Start IP Address and End IP Address to extend the scope.

Reduce the lease duration

To perform these procedures, you must be a member of the Administrators group, or you must have been delegated the appropriate authority.

To reduce the lease duration:

  • At the DHCP server, click Start, point to Administrative Tools, and then click DHCP.

  • In the DCHP console tree, right-click the scope you want to configure, and then click Properties.

  • On the General tab, under Lease duration for DHCP clients, type the new lease duration.

Decrease the cleanup interval

To perform these procedures, you must be a member of the Administrators group, or you must have been delegated the appropriate authority.

To use a Netsh command to set the cleanup interval time:

  • At the DHCP server, click Start, click Run, type cmd, and then press ENTER.

  • Type netsh dhcp set databasecleanupinterval "NewInterval" (where "NewInterval" is the amount of time in minutes between DHCP database cleanups).

Example

In the following example, this command sets the database cleanup interval to 10,080 minutes (every seven days).

netsh dhcp set databasecleanupinterval 10080

External References
This monitor does not contain any external references.

See Also for Windows Server 2016 DHCP Management Pack


Downloads for Windows Server 2016 DHCP Management Pack

AZURE OPTIMIZATION ASSESSMENT GET STARTED
MIGRATION TO AZURE GET STARTED
SYSTEM CENTER MIGRATION TO AZURE GET STARTED
MIGRATION TO AZURE FOR SQL AND WINDOWS 2008 GET STARTED